Toyota 4Runner Rear Bump Stops 2 Inch Plus Lift For 96-02 4Runner DuroBumps 5.25 inch Height

Proudly made in the USA, DuroBumps premium bump stops feature dual durometer (hardness) rubber to provide smooth, progressive dampening that greatly reduces hard bottom-outs, allowing for greater control and comfort compared to OEM bump stops, which can feel rock-hard on contact. DuroBumps eliminates the inchshell-shock inch effect experienced with OEM bump stops.

The DuroBumps DBR525 is the equivalent of using a 2 inch block spacer with OEM bump stops. The DBR525 limits wheel-up travel by 2 inch compared to OEM bump stops and is designed for trucks with a rear lift of 2 inch or more (fully loaded).
(For lifts less than 2 inch we offer a 3.5 inch version DBR354R)
Features and benefits

• Improved handling - Dual durometer rubber allows DuroBumps to act as a secondary coil spring, with smooth engagement that progressively increases compression load.
• Mounts in OEM location - Easily bolts into the OEM location, ensuring a proper fit with no modifications.
• No loss of up travel - Direct OEM replacement with no loss of suspension/wheel-up travel.
• Reduced tire rub - Reduced wheel-up travel means less tire rub in the wheel wells and less driveshaft contact on the OEM gas tank skid.
• Increased suspension life - Greatly extends the service life of other suspension components by absorbing the shock load from suspension bottom-outs. DuroBumps absorb the impact, saving critical suspension components from excessive wear and extending service intervals to the shocks, upper and lower control arm bushings, and panhard bar bushings.
• Small, compact, application specific - DuroBumps bump stops are designed to fit specific truck models. No universal fit spacers required.
• Smooth and silent - Unlike Hydro bumps, DuroBumps are whisper quiet on contact.
• Premium bump stops - DuroBumps are proudly made in the USA from the highest quality raw materials.
• Provided mounting hardware - JIS 10.9 zinc-coated hex head metric bolts and single-use thread locker are provided with every set of DuroBumps to ensure a strong, secure fit.

Note: For off-road use only. By installing these aftermarket bump stops on your vehicle, you assume all risk and liability. DuroBumps are not designed for towing applications. For more information, click here. Seller will not be held liable for any damages or loss associated with the installation or use of this product for any reason.

• 2 inch plus lift (Non-Long Travel)
• (recommended for 10 inch rear shock, equivalent to OEM bump stop w/ 2 inch block spacer) 1 inch at 1500 lbs Size: 3.75 dia. x 5.25 in. (ea.)
• Weight: 51 oz. / 3.18 lbs. (set)
• Part DBR525: Rear Bump Stops
• What's included:
• (2) Two 5.25 inch rear DuroBumps
• (2) Two JIS 10.9 M8-1.25 50 mm flange bolt
• (1) Single-use medium thread locker
• (1) One Free sticker

Tools required:

• Jack and jack stands
• 12 mm socket wrench
• 19 mm deep socket wrench or lug wrench
• Scraper or wire brush to clean debris
• Torque wrench

Step 1: Following vehicle manufacturer recommendations, use a properly rated jack. Lift the rear of the truck with floor jack and support the frame rails with jack stands. Remove rear wheels.
Be sure to use jack stands!
Step 2: Remove the OEM bump stop located on the frame rail above the rear axle tube, using a 12 mm deep socket.
Step 3: Use a scraper or wire brush to clean any mud/debris from the frame.
Step 4: Insert the flange bolt into the mounting hole of the DuroBumps and apply provided thread locker on the threads of the bolt. Mount DuroBumps in OEM location using a 12 mm socket wrench until snug (10 - 12 ft. lbs.). Do not over-tighten bolt.
Step 5: Repeat steps 2 - 4 on the other side.
Step 6: Reinstall wheels and lower vehicle back to the ground. Torque lug nuts to factory specifications.
Now go hit some trails or cruise the mall … whatever you're into!